1958 Cadillac Factory Shop Manual on CD-ROM. Covers all models. Original manual scanned to digital format. Click Here for more info. Includes the following books:

1. 1957 Cadillac Factory Shop Manual - covers all models ex. Brougham
2. 1958 Cadillac Shop Manual Supplement - covers all models ex. Brougham
3. 1946 - 1958 Cadillac Parts Book
4. 1956 - 1965 Cadillac Parts Book

PART #SM-57CA
$47.99 ea.

Cushion, Engine Support, Rear on Transmission (Transmission Mount) . Replaces original GM part #3631552. Re-vulcanization service only - core required. Allow 4 weeks for service.

• All models

Motor Mount. Replaces original GM part #1467058 & #1480098.

• All models

PART #05-001X
$45.00 / pair

Click to ENLARGE

Decal, Air Cleaner Service. Red letters on clear decal as original. For filter type A 59 C.

• All models w/ 3 x 2 carb

PART #DA0114
$5.75 ea.

Decal, Air Cleaner Service. Red letters on clear decal as original. For filter type A 63 C.

• All models w/ 4 BBL

PART #DA0113
$5.75 ea.

Grommet, Radiator Shroud. For headlight, turn signal, and horn wires. Replaces original exactly. 1-1/2" x 2-7/16".

• All models

PART #06-001G
$31.00 ea.

Seal, Headlight Outer Rim to sealed beam retainer ring. Fits all models with dual headlamps.

• All models

PART #06-003X
$31.30 ea.

Pad, Headlight Dimmer Switch. Rubber slip-over cover for floor mounted switch. 1-1/4" Outside diameter, 21/32" tall, 13/16" inner diameter.

• All models

PART #06-002P
$5.60 ea.

Weatherstrip, Taillight Housing to fender. 50" Strip, replaces original GM part #5949058.

• All models except Eldorado & Series 75

PART #06-005X
$2.80 ea.

Gasket, Taillight Lens. Replaces original GM part #5948189.

• Eldorado Seville [6237SDX] & Eldorado Biarritz [6267SX]
• Possible fit for Eldorado Brougham as well, but we have not confirmed this application.

PART #06-112P
$16.95 / pair

Gasket, Taillight Lens. Die cut 1/8" sponge rubber, 3-5/16" diameter. Replaces original GM part #5948280 & #5949216.

• All models except: Eldorado Brougham, Eldorado Seville, & Eldorado Biarritz

PART #06-010P
$20.25 / pair

Grommet, Taillight Wiring through trunk inner panel. 1 pair per car. 1-11/16" Diameter. Replaces original GM part #1467232.

• All models

PART #06-003G
$12.00 / pair

Gasket, Turn Signal & Parking Lamp Lens. Die cut from cork-rubber composite for a factory look and fit. Replaces original GM part #5949140.

• All models except Eldorado

PART #06-113P
$18.50 / pair

Gasket, Interior Dome Lamp Lens. Die cut from black sponge rubber for a factory look and fit.

• All models except convertibles

PART #18-002P
$12.00 ea.

Grommet, License Light Wire. 7/8" Diameter with 1/4" tapered hole. Special design replaces original GM part #1461493.

• Special Sport Cpe./Pow.Win. (Ht Eldorado) 6 Pass.
• Convt Coupe(Eldorado Biarritz)-Pow.Win.

PART #06-028P
$1.90 ea.

Pad, Antenna Mount. Molded replaces original GM #1469781.

• All models with factory installed antenna

PART #06-032P
$14.70 ea.

Grommet, Windshield Wiper control cable or gas gauge wire through rear compartment pan. Replaces original GM #4551272.

• All models

PART #03-001G
$1.30 ea.

Cover, Battery Clamp. Control unsightly sulphate build-up & help protect the nearby metal and finish. Available in black or red, sold separate.

PART #06-007X (black)
$8.00 ea.

PART #06-013X (red)
$8.00 ea.

Click to ENLARGE

Key Blank, W/ Cadillac Logo, Ignition & Door. Original GM part #3694624. This is a GM original part - New Old Stock (NOS) - limited supply. Used for ignition & door.

• All models

PART #06-001Y
CALL FOR PRICING & AVAILABILITY

Click to ENLARGE

Key Blank, W/ Cadillac Logo, Glovebox & Trunk. Original GM part #7029629. This is a GM original part - New Old Stock (NOS) - limited supply. Used for trunk and glovebox.

• All models

PART #06-002Y
$12.75 ea.

Click to ENLARGE

Key Blank, WITHOUT Cadillac Logo, Ignition & Door. Original GM part #3694624. This is a GM original part - New Old Stock (NOS) - limited supply. Used for ignition & door.

• All models

PART #06-015Y
$3.85 ea.

Click to ENLARGE

Key Blank, WITHOUT Cadillac Logo, Glovebox & Trunk. Original GM part #7029629. This is a GM original part - New Old Stock (NOS) - limited supply. Used for trunk and glovebox.

• All models

PART #06-016Y
$3.85 ea.

Rubber Spacers, Spark Plug Wires in organizer bracket. Replaces original GM part #1458862. Two required per vehicle.

• All models

PART #06-011X
$5.25 ea.

Grommet, Windshield Washer, Vacuum Lines, Antenna Lead, and others through firewall. Replaces original GM part #1456006.

• All models

PART #06-012G
$23.00 ea.

Grommet, Speedometer Cable through firewall. 1-3/8" Diameter.

• All models

PART #06-018G
$20.40 ea.

Grommet, Parking Brake Cable through firewall.

• All models

PART #06-016G
$19.00 ea.

Grommet, Radiator Shroud. For headlight, turn signal, and horn wires. Replaces original exactly. 1-1/2" x 2-7/16".

• All models

PART #06-001G
$31.00 ea.

Pad, Parking Brake locking pedal. Fully molded slip on type replaces original GM part #1466241. 1-1/2" Tall x 2-1/16" wide.

• All models

PART #08-004P
$9.20 ea.

Pad, Parking Brake release pedal. Fully molded slip on type replaces original GM part #1466654. 13/16" Tall x 2-5/8" wide.

• All models

PART #08-005P
$4.10 ea.

Bushing Kit, Propeller Shaft Retainer. Replaces original GM part #1466147 and #1466149. Six piece kit.

• All models

PART #09-002X
$44.40 / kit

Rear Bumper to Body Filler. Die cut from high quality, original style black masticated rubber for a factory fit. Replaces original GM part #1465941. Click Here to see where this item goes.

• All models except: Eldorado Seville [6237SDX], Eldorado Biarritz [6267SX], & Commercial Chassis [8680S]

PART #01-111M
$34.00 each

• All models except Eldorado Brougham

PART #01-103X
$155.75 / pair

Caps, Front Bumper Guard. Bumper "bullets." Replaces original GM part #1466583. Rubber with molded in plate and bolt.

• Eldorado Brougham only

PART #01-102X
$155.75 / pair

Radiator Seal Kit, 4 piece set, 2 per side. Die cut from high quality, original style black masticated rubber for a factory fit.

• All models except: Brougham

PART #02-101M
$36.00 / set

Tag, Freon Charge / AC Compressor. Perfect copy of original GM tag.

• All models with AC

PART #DA0240
$5.25 ea.

Decal, AC Compressor Warning. Perfect copy of original GM decal.

• All models with AC

PART #DA0029
$6.00 ea.

Fan Shroud Assembly Rubber, upper & lower. Assembly rubber fits between 2 upper, & 2 lower 180° bands.

• All models with factory AC

PART #02-109X
$19.50 / pair

***DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT***

A: Control Arm Shaft & Bushings, front upper, driver or passenger side, 2 kits required per car.

B: Control Arm (Rebound) Bumper, front upper, 2 required per car.

C: Ball Joint, front upper, driver or passenger side, 2 required per car.

D: Camber Eccentric - NOT AVAILABLE

E: Spring Insulator Cushion, front, mounts on coil top, 1 pair required per car.

***DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT***

F: Control Arm Bushings (Inner Assembly), front lower, driver or passenger side, 2 required per car.

G: Shock Bushing, front.

H: Lower Arm Bumper

I: Ball Joint, front lower, driver or passenger side, 2 required per car.

***DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT***

K: Stabilizer End Kit, 22 piece, 1 kit required per car.

L: Stabilizer/Sway Bar to Frame Bushing, 1 pair required per car.

***DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT***

M: Center Link

N: Outer Tie Rod End, passenger or driver side, 2 required per car.

O: Inner Tie Rod End - NOT AVAILABLE

P: Tie Rod Sleeve, passenger or driver side, 2 required per car.

**DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT.**

T: Rear Ball Joint

U: Control Yoke Bushing, manufactured as "1/2" bushings - 2 required per original bushing - 4 required total per car

V: Rear Spring Insulator

W: Rear Control Link Bushing (Front Side), 2 required per car

X: Rear Control Link Bushing (Rear Side), 2 required per car

Y: Bumper, Rear Cross Member or Frame

***DIAGRAM ABOVE IS FOR ILLUSTRATION ONLY. ACTUAL PARTS FOR YOUR VEHICLE MAY LOOK DIFFERENT***

Q: Spring Shackle Bushings, upper or lower, 12 required per car

R: Rubber Bumper, rear axle.

S: Rear Spring Insulator, upper or lower, 4 required per car

Dust Cover, Tie Rod Ends. Replaces original GM part #267026 and #505007.

• All models

PART #07-002X
$4.75 ea.

Seal, Lower Suspension Arm, Inner. Replaces original GM part #1464400. 4 required per car. 4 piece set.

• All models

PART #07-007X
$18.80 / kit

Seal, Upper A-arm, Inner. Replaces original GM part #1456574. 4 piece set.

• All models

PART #07-009X
$59.50 / kit

Grommet/Bushing. Flanged rubber grommet with metal sleeve bushing.

• All models, as required

PART #15-001G
$14.30 ea.

Firewall Insulator. Firewalls panels are an exact OEM replacement and are year, make, and model specific. They are molded to fit the engine setback and firewall contours like a glove. Firewalls come with basic installation holes cut or punched and the insulation backing.

• Eldorado Biarritz

PART #04-009N
$207.00 ea.

Firewall Insulator. Firewalls panels are an exact OEM replacement and are year, make, and model specific. They are molded to fit the engine setback and firewall contours like a glove. Firewalls come with basic installation holes cut or punched and the insulation backing.

• All models except Eldorado Biarritz

PART #04-010N
$207.00 ea.

Bumper, Front Hood Adjuster. 1-1/2" Long with 7/8" diameter bumper. Replaces original GM part #'s 1469648 & 1462588.

• All models except Eldorado

$5.70 ea.

Bumper, Front Hood Adjuster. 2" Long with 7/8" diameter bumper. Replaces original GM part #1457511 & #1469581. 4 per car.

• Eldorado only

$5.20 ea.

Bumper, Hood to Cowl, intermediate. Attaches to our hood to cowl weatherstrip Replaces original GM part #1457244, 45, 46. Various heights: 0.28", 0.34", & 0.40".

• All models as required

PART #04-115B (.28" tall)
$2.95 ea.

PART #04-116B (.34" tall)
$2.95 ea.

PART #04-117B (.40" tall)
$2.95 ea.

Bumper, Hood Side to Fender. Mounts on fender, two required per side, 4 per car. Replaces original GM part #1456568.

• All models

PART #04-107B
$4.25 ea.

Bumper, Front Fender to Hood. 13/16" Diameter. Replaces original GM part #1471438. 6 used per car.

• All models

PART #03-001B
$2.40 ea.

Bumpers, Hood. 4 required per car, 4 included in kit. 9/16" Tall by 9/16" wide by 1-7/16" long.

• Most models as required including Eldorado Brougham
  

PART #04-121B
$27.00 / kit

Weatherstrip, Hood to Cowl. Extruded material cut 52" long. Replaces original GM part #4220564 & 4698277.

• All models except Eldorado Brougham

PART #04-103C
$40.00 ea.

Weatherstrip, Hood to Cowl. Correct cross section extrusion cut 44" long. Replaces original GM part #4689677.

• Eldorado Brougham only

PART #04-105C
$82.55

Weatherstrip, Hood to Fender, exact copy of original profile. Approximately 36" long.

• Eldorado Brougham only

PART #04-103X
$128.50 / pair

Sealing Strip, Fender Skirt Edge to Body. Two strips 72" long replacing original GM part #1470133.

• Fleetwood 60 Special only

PART #14-004X
$35.10 / pair

Pad and Seal, Fender Skirt Edge. Exact copy, trim notch for skirt lock at installation. 1/2" Thick x 7/16" tall. Two 5' strips, enough for 2 fender skirts.

• Most models including Eldorado Brougham

PART #14-003X
$45.00 / pair

Cover, Rocker Panel Inner Dust Shield. Replaces original GM part #4615576 perfectly. Fully molded with proper attaching teeth and flap. Found typically on two door cars, and serves as a cover for the drain in the fender in front of the rear tires. If you have a rectangular hole above a half moon hole about a foot in front of your rear tires facing towards the propeller shaft, this is the seal for those holes.

• All 2 door models

PART #03-005X
$11.00 / pair

Splash Apron Set. Die cut from original style masticated rubber for a factory fit. Pieces fit over a-arm, and inside inner fenders. Six piece kit, 3 per side. Staples are included.

• All models ex. Brougham

PART #03-101M
$44.99 / kit

Rear Wheelhouse Seals. Die cut from high quality, original style black masticated rubber for a factory fit. All mounting hardware holes are pre-cut.

• Most models as required

PART #03-113M
$19.99 / pair

Filler, Aux. Wheelhouse to Inner Fender. Die cut from high quality, original style black masticated rubber for a factory fit. All mounting hardware holes are pre-cut.

• Most models as required

PART #03-155M
$10.00 / pair

Rear Bumper to Body Filler. Die cut from high quality, original style black masticated rubber for a factory fit. Replaces original GM part #1465941. Click Here to see where this item goes.

• All models except: Eldorado Seville [6237SDX], Eldorado Biarritz [6267SX], & Commercial Chassis [8680S]

PART #01-111M
$25.00 each

Plug, Body Sheet Metal Holes. Used in various places (like trunks). 2 1/4" Diameter head, fits 1-1/2" diameter hole in body. Click here to see other size body plugs.

• All models as required

PART #20-019X
$3.25 ea.

Seal or Anti-Squeak, inner fender dust shield (splash shield), bulb type seal with stapling flange. Used many years, many applications. 1-1/4" wide with 1/4" bulb. Sold in 12' strips.

PART #03-002X
$36.00 / 12 feet

Seal, Rear Bumper to Body. Replaces original GM part #1460847. Includes two 30" strips of extrusion.

• Commercial Chassis only

PART #03-004X
$58.50 / pair

Pad, Body Mounting. 2" square with 15/16" hole. Replaces original GM part #1447317.

• All models

PART #03-101H
$6.80 ea.

Pad, Body Mounting. Correct molded replacement for original GM part #1461768 & #1476996 with metal tube and washer core.

• All models except convertibles

PART #03-106H
$11.10 ea.

Pad, Body Mounting to Chassis. Approximately 1-7/8" outside diameter, 11/16" inside diameter, 9/16" thick. Replaces original GM part #1461987.

• All models except convertibles

PART #03-107H
$6.80 ea.

Pad, Body Mounting to Chassis. Approximately 1-7/8" outside diameter, 15/16" inside diameter, 9/16" thick. Replaces original GM part #1468935.

• All models

PART #03-108H
$6.80 ea.

Pad, Body Mounting to Chassis. Square type approximately 2-3/16" outside dimension, 3/4" inside diameter hole, 1/2" thick. Replaces original GM part #1461991.

• All models except convertibles

PART #03-109H
$6.80 ea.

Rear Quarter Window Leading Edge Seal. These weatherstrip's will have a metal core if required for proper operation.

Division Bar Seal. Rear door on models with rear door vent.

• All sedan models except Eldorado Brougham & Series 75

PART #10-047X
$30.10 / pair

Rear Vent Window Weatherstrip, rear door. Fully molded replacements. Use with our rear vent division bar seal #10-047X (listed above.)

• All sedan models except Eldorado Brougham & Series 75

PART #10-006X
$146.00 / pair

Post Model Window Channel & Beltline Kit.

Includes: Two five foot sections of window run channel PART #10-013X, Four three foot sections of inner and outer beltline PART #10-049X, One pair of upper division channel seal PART #10-012X, & One pair lower division channel seals PART #10-016X.

Each kit provides enough for two doors (4 door post models order two kits.)

• All 2 & 4 door post models

PART #10-022X
$142.50 / set

Beltline "Window Fuzzies" or "Sweepers," Inner & Outer. Used on doors, rear quarters, inner & outer. Made with chrome bead, mohair faced, flexible, 7/16" wide X 15/64" thick. Trim length where necessary. Also available in 9/16" wide.

• Most models, as required - call for a free sample

PART #10-049X
$19.00 each (6' strip)

Window Run Channel, flexible snap-in, window glass run, front and rear doors. Flexible pile lining with rubber covering. 6 foot strip.

• Most closed models - compare original to sketch or call for a free sample

PART #10-017X
$38.60 / 6' strip

Window Run Channel, bright stainless beaded edge. Cloth covered, mohair lined, FLEXIBLE metal channel for sides and top of door windows. Perfect dimensions, 5/8" wide X 9/16" overall height, exact replacement. Sold in either 5' or 6' lengths.

• Most closed models - compare original to sketch or call for a free sample

PART #10-013X (5' strip)
$24.00 ea.

PART #10-014X (6' strip)
$26.00 ea.

Channel, Rigid Run, used on back side of division bar below beltline. Zinc plated steel with cloth insert - 1/2" deep x 1/2" wide x 15" long. ***This material is also available by the foot. Contact your RTRW salesperson for details.***

• Most models, as required - call for a free sample

PART #10-016X
$21.10 / pair (15" strips)

Channel, Door Window Lower Sash. Attaches to window lift assembly, and holds door glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required. Virtually all GM models. Sold in 4 ft. strips, usually sufficient for 2 windows. Formed steel channel only, not chromed. Ready for attaching to your old brackets. Use our sash channel fillers to set door glass into channel.

• All models, as required - call for a free sample

PART #10-045X
$23.20 ea.

Window Sash, Door & Vent. Replaces original GM part #4099013-4. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Used on many models.

• Some models - call for a free sample

PART #10-015X
$5.70 / ft.

Filler Strip, Sash Channel, for all applications fitting glass to sash channel not requiring weather strip type of filler. Check your old filler strip to find thickness needed. Constructed of a rubber-like polymer designed for setting glass in a metal sash channel. This item is not returnable except for quality assurance issues. Order by the foot.

• Many models, as required - call for a free sample

PART #10-043X (1/32" thick)
$1.10 / ft.

PART #10-044X (1/16" thick)
$1.10 / ft.

Liner, Mohair – Felt liner with a rubber backing – for use on window guides & channels where no direct replacement is available - CALL FOR A FREE SAMPLE

PART #10-079X (2-1/2" wide)
$3.25 / FT

PART #10-80X (1-1/2" wide)
$2.75 / FT

Cushion, Window Stop, lower (stem bumper). Replaces original GM part #4114117, #4665181, #4672308, & #4814044. For front and rear door, rear side and quarter windows as required. 15/16" Square x 1/2" thick with "carrot" type retainer.

• Some models, as required

PART #10-001B
$4.80 ea.

Cushion, Window Stop, lower (stem bumper). Replaces original GM part #4031052, for front and rear door, rear side and quarter windows as required. 7/8" Square x 5/16" thick.

• Most models, as required

PART #10-002B
$9.20 / pair

Pad, Vent Window Frame, self-retaining, 1/2" diameter X 5/32" high, for 3/16" hole.

• Eldorado Brougham

PART #10-011B
$1.30 ea.

Convertible Roof Rail Weatherstrip. The roof rail is the section typically over the side and rear quarter windows when the top is up. The roof rail kit contains 9 pieces, including the front bow seal. The hinge pillar section is the weatherstrip typically between the windshield post and the front door opposite the vent window. The hinge pillar kit contains 2 pieces, pair, L & R. Kits are sold separately.

Hardtop Roof Rail Seals. The roof rail seals seal the tops of the windows to the body. Made with molded ends to factory specifications for an exact fit.

Grommet, Folding Top Hydraulic Pump Mount. Special design to hold pump mounting bracket to floor pan. Replaces original GM part #3698109. Four (4) needed per car.

• All convertibles

PART #13-001G
$1.40 ea.

Spacer, Folding Top Power Cylinder Support. 4 used per car. Replaces original GM part #4149726.

• All convertibles

PART #13-009X
$2.90 ea.

Tape, Bow Drill Cloth, pressure sensitive, for covering convertible side window weatherstrip. Water & sun proof. Available in black or tan, 2-1/2" wide X 5 ft. roll.

PART #13-004X (black, 2.5" wide)
$8.25 / 5 ft. roll

PART #13-006X (tan, 2.5" wide)
$8.25 / 5 ft. roll

Tape, Bow Drill Cloth, pressure sensitive, for covering convertible side window weatherstrip. Water & sun proof. Available in black or tan, 5 " wide X 5 ft. roll.

PART #13-005X (black, 5 " wide)
$20.50 / 5 ft. roll

PART #13-007X (tan, 5 " wide)
$20.50 / 5 ft. roll

Door Weatherstrip Kits. High quality reproductions made with molded ends and clips as required. If you do not see your model listed in this section, please refer to our "Door Seals By the Foot" in the next section.

Weatherstrip, Door Edge. Use this seal if we do not have an exact match for your model in the "door weatherstrip kits" listed in the previous section. Great for ambulance, hearse, etc. For cement-on or nylon fastener applications. Available with or without molded in clips. Compare your original seal profile to the sketch. Sold by the foot.

PART #12-014X (without clips)
$3.50 / ft.

PART #12-015X (with clips)
$4.90 / ft.

Door Lock Pillar Seals. These weatherstrip's are normally used to seal the bottom edge of a quarter or rear side window on the lock pillar of the body. These fillers will have a metal core if required for proper operation.

Seal, Roof Rail, outer at 1/4 window. Replaces original GM part #4650269-70.

• All hardtop coupes

PART #12-034X
$17.90 / pair

Weatherstrip, Front Door Auxiliary, on door at beltline, right and left. Replaces original GM part #4698923-4, #4654139-40, uses snap-in fasteners (4 each included in set).

• All models except Eldorado Brougham

PART #12-031X
$28.00 / pair

Weatherstrip, Rear Door Hinge Pillar at beltline Replaces original GM part #4734198. 2 per car. 2 piece set.

• Eldorado Brougham

PART #12-033X
$33.30 / pair

Weatherstrip, Door Bottom drain hole seal. 4-1/2" Long, replaces original GM part #4676124.

• All models

PART #12-002X
$3.25 ea.

Weatherstrip, Rear Door Hinge Pillar. Replaces original GM part #4698887-8.

• All models except Brougham, Series 75

PART #12-006X
$44.70 / pair

Bumper, Door Edge. Replaces original GM part #4431695. Typically 2 per door. 3/4" Tall x 1 1/16" long x 9/16 thick. We carry this type of bumper in many sizes. If you can't find the one you need please give us a call or visit our "Door Bumpers" page to view all available sizes.

• All models

PART #12-015B
$1.25 ea.

Bumper, Door Edge, twin retainer style. 13/16" long x 1/2 " tall x 3/8 " thick. We carry this type of bumper in many sizes. If you can't find the one you need please give us a call or visit our "Door Bumpers" page to view all available sizes.

• Some sedan models

PART #12-006B
$2.25 ea.

Bumper, Rear Door, twin retainer style. 15/16" long x 3/8" tall x 1/2" thick. We carry this type of bumper in many sizes. If you can't find the one you need please give us a call or visit our "Door Bumpers" page to view all available sizes.

• Some sedan models

PART #12-005B
$2.25 ea.

Bumper, Rear Door. Replaces original GM part #4762475. Compare to original, use as required. We carry this type of bumper in many sizes. If you can't find the one you need please give us a call or visit our "Door Bumpers" page to view all available sizes.

• Some models

PART #12-014B
$1.25 ea.

Bumper, Front Door above the upper hinge on the upper radius of the door. Stiff backed, retained by screw.

• All closed models

PART #12-001B
$3.15 ea.

Bumper, Door Lock Post, Upper, 1/2" diameter X 1/2" diameter X 1/2" tall, plated screw.

• Most models, including Eldorado Brougham

PART #12-007B
$2.80 ea.

Door Handle Gasket Kit. Six piece kit, enough for two handles. Includes rubber washers for plunger button.

• All 2 door hardtop & convertibles.
• Series 62 hardtop sedan & Sedan DeVille

PART #12-010P
$17.50 / kit

Mounting Pad, Rear View Mirror. Die cut to exact GM specifications.

• All models

PART #12-014P
$6.00 each

Bumper, Door Lock Striker Plate. Replaces original GM part #4746647. Rubber with steel core, 7/16" thick, 1 per door. Installed in rotary latch receiver. 1-1/8" Tall x 9/16" wide.

• Eldorado Brougham

PART #12-009B
$18.00 ea.

Weatherstrip, Deck Lid/Trunk. Cut to length, excellent quality rubber sponge more durable than original.

• All models except Eldorado Brougham

PART #16-003T
$19.00 ea.

Bumper, Deck Lid, cap type for adjustable screw, 15/16" O.D., 7/16" thick.

• Many models, as required

PART #17-001B
$1.45 ea.

Bumper, Deck Lid opening on lid. Replaces OEM #4114321. Metal core, as original, 2 required, screw held.

• Convertibles only

PART #17-003B
$4.60 ea.

Bumper, Deck Lid, self-retaining. 7/8" O.D., 5/16" thick, fits 1/4" hole. Replaces original GM part #4721222.

• All models except HT Eldorado, Eldorado Biarritz

PART #17-005B
$1.15 ea.

Gasket, Door & Trunk Lock Cylinder. Exact reproduction of original GM part #4587931. 7/8" I.D.

• All models

PART #12-009P
$1.00 ea.

T-Nut, Deck lid Bumper in gutter at sides, steel core, approx. 1/2" X 1/2" X 1". Core tapped 10-32 thread. 2 required per car. Replaces #4606237.

• All models having partial w/strip in gutter of body

PART #17-004B
$13.90 ea.

Jack Instructions Decal. Identical to original.

• All models except Biarritz

PART #DA0005
$4.75 ea.

Jack Instructions Decal. Identical to original.

• Eldorado Biarritz

PART #DA0011
$4.75 ea.

Air Suspension Warning Card. Identical to original.

• All models w/ air suspension

PART #DA0012
$3.55 ea.

Bumper, Glove Box Door. For 1/8" to 5/32" hole, 5/32" thick pad, 5/16" diameter.

• Many models, as required

PART #18-001B
$0.80 ea.

Bumper, Glove Box Door. For 1/8" to 5/32" hole, 1/4" thick pad, 5/16" diameter.

• Many models, as required

PART #18-002B
$0.80 ea.

Grommet, Sun Visor Rod. Made of gray rubber, 3/4" long.

• All models

PART #18-006X
$1.75 ea.

Trip Meter Reset Knob . Made of black rubber. 1/8" I.D., 7/16" O.D. X 1/2" tall.

• All models

PART #18-007X
$5.00 ea.

Gasket, Interior Dome Lamp Lens. Die cut from black sponge rubber for a factory look and fit.

• All models except convertibles

PART #18-002P
$12.00 ea.

Grommet, Dimmer Switch for carpet application, 2-3/4" O.D., wide flange for stitching, 1" hole for dimmer switch.

• Closed bodies, many models

PART #18-001G
$7.30 ea.

Grommet, Instrument Panel to Windshield Frame. 2-6 required. Replaces original GM part #4614412.

• All models

PART #18-005G
$5.90 ea.

Grommet, Glove Box door cushion. Replaces original GM part #4671566.

• All models

PART #18-005B
$8.50 ea.

Grommet, Steering Column at Floor. Fully molded, replaces original GM part #1467403.

• All models

PART #18-007G
$42.50 ea.

Click to ENLARGE

Seal, Steering Column to Firewall. Replaces original GM part #1464097.

• All models

PART #18-004X
$45.00 ea.

Click to ENLARGE

Flat Speed Nut. Used on most models for many applications.

U-Nut. Used on most models for many applications.

Pal Nut W/ Sealer. Used to attach various trim, badges, & name plates. Special rubber sealer on backside as original. Used on most models for many applications.

Fastener, Hood to Cowl weatherstrip (and other uses), self-retaining steel button, 11/16" head, for 5/16" hole but will fit down to 1/4" hole. Replaces original GM part #4824561, #4583318, & #1472713.

• All models as required

PART #04-100F
$1.15 ea.

Fastener, Auxiliary Weatherstrip on door edge. Replaces original GM part #4801268. Nylon, self-locking button, for 1/8" hole, 13/32" diameter head. Similar to 12-001F but made of nylon.

• All models

PART #12-003F
$1.00 ea.

3M™ Adhesive Remover. Quickly removes wax, grease, oil and adhesive residue. It will not harm most cured automotive paints and is also suitable for vinyl and glass surfaces. 8 oz. can.

PART #23-002X
$13.00 / 8 oz. can

3M™ Super Weatherstrip Adhesive (BLACK) is a strong, flexible, rubbery adhesive that can withstand vibration, oil, grease, and extreme temperature variations. It can be used to bond weatherstripping to car doors, trunks, T-tops, moon roofs and sun roofs. It is an excellent adhesive for holding paper, cork, or rubber gaskets in place during installation. It provides the strength and rapid setting needed to hold weatherstripping, headliners, and side panels in place. 5 oz. tube.

PART #23-003X
$11.00 / 5 oz. tube

3M™ Super Weatherstrip Adhesive (YELLOW) is a strong, flexible, rubbery adhesive that can withstand vibration, oil, grease, and extreme temperature variations. It can be used to bond weatherstripping to car doors, trunks, T-tops, moon roofs and sun roofs. It is an excellent adhesive for holding paper, cork, or rubber gaskets in place during installation. It provides the strength and rapid setting needed to hold weatherstripping, vinyl headliners, and side panels in place. 5 oz. tube.

PART #23-001X
$11.00 / 5 oz. tube